waybas.blogg.se

1. #Mini vci j2534 driver windows 10 how to#
2. #Mini vci j2534 driver windows 10 64 Bit#
3. #Mini vci j2534 driver windows 10 full#
4. #Mini vci j2534 driver windows 10 windows 10#
5. #Mini vci j2534 driver windows 10 software#

#Mini vci j2534 driver windows 10 how to#

Q: How to install Techstream v10 on Windows 64 bit?Ī: Quick note on techstream 10.x with windows 7 or greater 圆4 with the 1.4.1 (and possibly the 2.0.1) Mini VCI cable. I thought the Win10 instructions were a little confusing but I worked thru it. But going forward I presume that’ll be harder to find. That would be great if you have an XP laptop (or desktop) available…it is definitely a much easier install. Which is why I up telling people to stick with using an XP laptop instead.

If capable of 64-bit, then they give you a small CD with some special files “XHorse” and it takes a little bravery to mess with your Registry etc.ītw, Many people will not be able to follow the instructions to install the necessary cominents. I think the first requirement is that your mini VCI cable hardware is capable of 32 and 64 bit, I think some of the earlier cables may be 32-bit (XP) only. Q: Can you post the instructions or a good link for installation on win 10 ?Ī: This link describes the installation process, possibly with link to the software.

#Mini vci j2534 driver windows 10 software#

The guy I share the Prolong setup with used the version 12 software on his 2007, so it’ll work on a Gen2 ). Q: What version of Techstream is compatible with the 2nd gen? Will v12 work?Ī: I had 12.xx.024 for a bit but it was minus several menus needed for better diagnostics:(. The other option, find a cheap laptop on eBay or CL with Win 7 and follow the VxDaig Nano instructions and it will load right up.

#Mini vci j2534 driver windows 10 64 Bit#

However, the driver for VxDaig Nano (which is what I think you meant) is not a 64 bit driver, so you will need to go back the sellers of VxDaig and seek their support to load it on a 64-bit system. Q: I am trying to download a version of Techstream to my Windows 10, 64 bit computer, so I may use my new VCX Nano to diagnose my car issue- won’t start after 6 weeks sitting dormant.Ī: Techstream has been compatible with 64 bit OSes for a while, so I don’t think that is your problem.

#Mini vci j2534 driver windows 10 windows 10#

Here are easy directions for newbies to install/setup Techstream on Windows 10 64 bit for VXDIAG VCX NANO Toyota. It uses the ISO 9141-2 protocol like all of the T22s although I noticed some of the later 02 models, 52 plates, that they had some of the 2 wire hi/lo cabling used by canbus but whether that meant they actually used an early canbus version or the harnesses were starting to be made compliant for canbus in preparation for the T25 I'm not entirely sure.Techstream definitely works with the Microsoft Windows 10 (圆4) operating system. The K and L line are used with the earlier OBD2 models like my 02 T22.

#Mini vci j2534 driver windows 10 full#

Have you all purchased the full programme with all the relevant passwords or codes and if so how. Without the particular code I could only run a highly reduced version of techstream which was pretty poor to be honest. Purely out of interest as I have downloaded Techstream in the past and had it running on my laptop with Windows 10.Īlways though it asks for a specific official code that you have to enter to demonstrate that it's a legitimate fully purchased copy and that you are a proper garage etc. Sorry I can't be more helpful, but I can only go by my setup. My car does not support all modules being a TR, if you click on a module not supported, you are notified. When I launch into Techstream, I do the usual -connect mini VCI cable to OBD socket, ignition on, confirm the make of the car, a menu option comes up with ' -11, 11-15, 15-', I choose '-11' and then on the next menu 'w/out smart key'. I tried removing the the codes using the Launch, jumper link via the OBD and Delphi. I use my standalone Launch scanner to calibrate the EPB, but it did a reset and remove the zeropoint calibrations for clutch and g-force. I was forced to use Techstream earlier this year, when I had a problem with EPB. I have other diagnostic software loaded, and they work using another USB adapter. The only thing that let's the Netbook down is the screen resolution is a little low, but works fine most of the time. I have to admit that I don't remember how I got everything working, but I am using an old Netbook with Windows XP.